68 lines
3.2 KiB
C
68 lines
3.2 KiB
C
///////////////////////////////////////////////////
|
|
// Setup for STM32 Nucleo and ILI9341 display //
|
|
///////////////////////////////////////////////////
|
|
#define USER_SETUP_ID 33
|
|
|
|
// Last update by Bodmer: 28/11/19
|
|
|
|
// STM32 optimised functions are not yet compatible with STM32H743 processor.
|
|
// The STM32H743 does work with the slower generic processor drivers
|
|
//
|
|
// REMINDER - Nucleo-F743ZI and Nucleo-F743ZI2 have different pin port allocations
|
|
// and require appropriate selection in IDE. ^---- Note the extra 2 in part number!
|
|
|
|
|
|
// Define STM32 to invoke STM32 optimised driver (optimised fns only tested on STM32F767 so far)
|
|
// so you may need to comment this out
|
|
#define STM32
|
|
|
|
// Define the TFT display driver
|
|
#define RPI_DISPLAY_TYPE
|
|
#define ILI9486_DRIVER
|
|
|
|
// MOSI and SCK do not need to be defined, connect:
|
|
// - Arduino SCK to TFT SCK
|
|
// - Arduino MOSI to TFT SDI(may be marked SDA or MOSI)
|
|
// Standard Arduino SPI pins are(SCK=D13, MOSI=D11) this is port pins PA5 and PA7 on Nucleo-F767ZI
|
|
|
|
// Can use Ardiuno pin references, arbitrary allocation, TFT_eSPI controls chip select
|
|
#define TFT_CS D5 // Chip select control pin to TFT CS
|
|
#define TFT_DC D6 // Data Command control pin to TFT DC (may be labelled RS = Register Select)
|
|
#define TFT_RST D7 // Reset pin to TFT RST (or RESET)
|
|
|
|
// Alternatively, we can use STM32 port reference names PXnn
|
|
//#define TFT_CS PE11 // Nucleo-F767ZI equivalent of D5
|
|
//#define TFT_DC PE9 // Nucleo-F767ZI equivalent of D6
|
|
//#define TFT_RST PF13 // Nucleo-F767ZI equivalent of D7
|
|
|
|
//#define TFT_RST -1 // Set TFT_RST to -1 if the display RESET is connected to processor reset
|
|
// Use an Arduino pin for initial testing as connecting to processor reset
|
|
// may not work (pulse too short at power up?)
|
|
|
|
// Chip select for XPT2046 touch controller
|
|
//#define TOUCH_CS D4
|
|
|
|
#define LOAD_GLCD // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
|
|
#define LOAD_FONT2 // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
|
|
#define LOAD_FONT4 // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
|
|
#define LOAD_FONT6 // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
|
|
#define LOAD_FONT7 // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
|
|
#define LOAD_FONT8 // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
|
|
#define LOAD_GFXFF // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
|
|
|
|
// STM32 support for smooth fonts via program memory (FLASH) arrays
|
|
#define SMOOTH_FONT
|
|
|
|
|
|
// Nucleo-F767ZI has a ~216MHZ CPU clock, this is divided by 4, 8, 16 etc
|
|
|
|
#define SPI_FREQUENCY 20000000 // 27MHz SPI clock
|
|
//#define SPI_FREQUENCY 55000000 // 55MHz is over-clocking ILI9341 but seems to work reliably!
|
|
|
|
//#define SPI_READ_FREQUENCY 15000000 // Reads need a slower SPI clock, probably ends up at 13.75MHz (CPU clock/16)
|
|
|
|
//#define SPI_TOUCH_FREQUENCY 2500000 // Must be very slow
|
|
|
|
// This has no effect, transactions for STM32 are automatically enabled
|
|
#define SUPPORT_TRANSACTIONS
|