95 lines
2.3 KiB
Arduino
95 lines
2.3 KiB
Arduino
|
/*
|
||
|
|
RadioLib AX.25 Transmit Example
|
||
|
|
|
||
|
|
This example sends AX.25 messages using
|
||
|
|
SX1278's FSK modem.
|
||
|
|
|
||
|
|
Other modules that can be used for AX.25:
|
||
|
|
- SX127x/RFM9x
|
||
|
|
- RF69
|
||
|
|
- SX1231
|
||
|
|
- CC1101
|
||
|
|
- SX126x
|
||
|
|
- nRF24
|
||
|
|
- Si443x/RFM2x
|
||
|
|
|
||
|
|
For default module settings, see the wiki page
|
||
|
|
https://github.com/jgromes/RadioLib/wiki/Default-configuration
|
||
|
|
|
||
|
|
For full API reference, see the GitHub Pages
|
||
|
|
https://jgromes.github.io/RadioLib/
|
||
|
|
*/
|
||
|
|
|
||
|
|
// include the library
|
||
|
|
#include <RadioLib.h>
|
||
|
|
|
||
|
|
// SX1278 has the following connections:
|
||
|
|
// NSS pin: 10
|
||
|
|
// DIO0 pin: 2
|
||
|
|
// RESET pin: 9
|
||
|
|
// DIO1 pin: 3
|
||
|
|
SX1278 radio = new Module(10, 2, 9, 3);
|
||
|
|
|
||
|
|
// or using RadioShield
|
||
|
|
// https://github.com/jgromes/RadioShield
|
||
|
|
//SX1278 radio = RadioShield.ModuleA;
|
||
|
|
|
||
|
|
// create AX.25 client instance using the FSK module
|
||
|
|
AX25Client ax25(&radio);
|
||
|
|
|
||
|
|
void setup() {
|
||
|
|
Serial.begin(9600);
|
||
|
|
|
||
|
|
// initialize SX1278
|
||
|
|
Serial.print(F("[SX1278] Initializing ... "));
|
||
|
|
// carrier frequency: 434.0 MHz
|
||
|
|
// bit rate: 1.2 kbps (1200 baud 2-FSK AX.25)
|
||
|
|
int state = radio.beginFSK(434.0, 1.2);
|
||
|
|
|
||
|
|
// when using one of the non-LoRa modules for AX.25
|
||
|
|
// (RF69, CC1101,, Si4432 etc.), use the basic begin() method
|
||
|
|
// int state = radio.begin();
|
||
|
|
|
||
|
|
if(state == RADIOLIB_ERR_NONE) {
|
||
|
|
Serial.println(F("success!"));
|
||
|
|
} else {
|
||
|
|
Serial.print(F("failed, code "));
|
||
|
|
Serial.println(state);
|
||
|
|
while(true);
|
||
|
|
}
|
||
|
|
|
||
|
|
// initialize AX.25 client
|
||
|
|
Serial.print(F("[AX.25] Initializing ... "));
|
||
|
|
// source station callsign: "N7LEM"
|
||
|
|
// source station SSID: 0
|
||
|
|
// preamble length: 8 bytes
|
||
|
|
state = ax25.begin("N7LEM");
|
||
|
|
if(state == RADIOLIB_ERR_NONE) {
|
||
|
|
Serial.println(F("success!"));
|
||
|
|
} else {
|
||
|
|
Serial.print(F("failed, code "));
|
||
|
|
Serial.println(state);
|
||
|
|
while(true);
|
||
|
|
}
|
||
|
|
}
|
||
|
|
|
||
|
|
void loop() {
|
||
|
|
// send AX.25 unnumbered information frame
|
||
|
|
Serial.print(F("[AX.25] Sending UI frame ... "));
|
||
|
|
// destination station callsign: "NJ7P"
|
||
|
|
// destination station SSID: 0
|
||
|
|
int state = ax25.transmit("Hello World!", "NJ7P");
|
||
|
|
if (state == RADIOLIB_ERR_NONE) {
|
||
|
|
// the packet was successfully transmitted
|
||
|
|
Serial.println(F("success!"));
|
||
|
|
|
||
|
|
} else {
|
||
|
|
// some error occurred
|
||
|
|
Serial.print(F("failed, code "));
|
||
|
|
Serial.println(state);
|
||
|
|
|
||
|
|
}
|
||
|
|
|
||
|
|
delay(1000);
|
||
|
|
}
|