188 lines
8.9 KiB
C
188 lines
8.9 KiB
C
|
// USER DEFINED SETTINGS
|
||
|
|
// Set driver type, fonts to be loaded, pins used and SPI control method etc
|
||
|
|
//
|
||
|
|
// See the User_Setup_Select.h file if you wish to be able to define multiple
|
||
|
|
// setups and then easily select which setup file is used by the compiler.
|
||
|
|
//
|
||
|
|
// If this file is edited correctly then all the library example sketches should
|
||
|
|
// run without the need to make any more changes for a particular hardware setup!
|
||
|
|
// Note that some sketches are designed for a particular TFT pixel width/height
|
||
|
|
|
||
|
|
#define USER_SETUP_ID 60
|
||
|
|
// ##################################################################################
|
||
|
|
//
|
||
|
|
// Section 1. Call up the right driver file and any options for it
|
||
|
|
//
|
||
|
|
// ##################################################################################
|
||
|
|
|
||
|
|
// Tell the library to use 8 bit parallel mode (otherwise SPI is assumed)
|
||
|
|
//#define TFT_PARALLEL_8_BIT
|
||
|
|
|
||
|
|
// Display type - only define if RPi display
|
||
|
|
//#define RPI_DISPLAY_TYPE // 20MHz maximum SPI
|
||
|
|
|
||
|
|
// Only define one driver, the other ones must be commented out
|
||
|
|
#define ILI9341_DRIVER
|
||
|
|
//#define ST7735_DRIVER // Define additional parameters below for this display
|
||
|
|
//#define ILI9163_DRIVER // Define additional parameters below for this display
|
||
|
|
//#define S6D02A1_DRIVER
|
||
|
|
//#define RPI_ILI9486_DRIVER // 20MHz maximum SPI
|
||
|
|
//#define HX8357D_DRIVER
|
||
|
|
//#define ILI9481_DRIVER
|
||
|
|
//#define ILI9486_DRIVER
|
||
|
|
//#define ILI9488_DRIVER // WARNING: Do not connect ILI9488 display SDO to MISO if other devices share the SPI bus (TFT SDO does NOT tristate when CS is high)
|
||
|
|
//#define ST7789_DRIVER // Full configuration option, define additional parameters below for this display
|
||
|
|
//#define ST7789_2_DRIVER // Minimal configuration option, define additional parameters below for this display
|
||
|
|
//#define R61581_DRIVER
|
||
|
|
//#define RM68140_DRIVER
|
||
|
|
//#define ST7796_DRIVER
|
||
|
|
//#define SSD1963_480_DRIVER
|
||
|
|
//#define SSD1963_800_DRIVER
|
||
|
|
//#define SSD1963_800ALT_DRIVER
|
||
|
|
//#define ILI9225_DRIVER
|
||
|
|
|
||
|
|
// Some displays support SPI reads via the MISO pin, other displays have a single
|
||
|
|
// bi-directional SDA pin and the library will try to read this via the MOSI line.
|
||
|
|
// To use the SDA line for reading data from the TFT uncomment the following line:
|
||
|
|
|
||
|
|
// #define TFT_SDA_READ // This option is for ESP32 ONLY, tested with ST7789 display only
|
||
|
|
|
||
|
|
// For ST7735, ST7789 and ILI9341 ONLY, define the colour order IF the blue and red are swapped on your display
|
||
|
|
// Try ONE option at a time to find the correct colour order for your display
|
||
|
|
|
||
|
|
// #define TFT_RGB_ORDER TFT_RGB // Colour order Red-Green-Blue
|
||
|
|
// #define TFT_RGB_ORDER TFT_BGR // Colour order Blue-Green-Red
|
||
|
|
|
||
|
|
// For ST7789, ST7735 and ILI9163 ONLY, define the pixel width and height in portrait orientation
|
||
|
|
// #define TFT_WIDTH 80
|
||
|
|
// #define TFT_WIDTH 128
|
||
|
|
// #define TFT_WIDTH 240 // ST7789 240 x 240 and 240 x 320
|
||
|
|
// #define TFT_HEIGHT 160
|
||
|
|
// #define TFT_HEIGHT 128
|
||
|
|
// #define TFT_HEIGHT 240 // ST7789 240 x 240
|
||
|
|
// #define TFT_HEIGHT 320 // ST7789 240 x 320
|
||
|
|
|
||
|
|
// For ST7735 ONLY, define the type of display, originally this was based on the
|
||
|
|
// colour of the tab on the screen protector film but this is not always true, so try
|
||
|
|
// out the different options below if the screen does not display graphics correctly,
|
||
|
|
// e.g. colours wrong, mirror images, or tray pixels at the edges.
|
||
|
|
// Comment out ALL BUT ONE of these options for a ST7735 display driver, save this
|
||
|
|
// this User_Setup file, then rebuild and upload the sketch to the board again:
|
||
|
|
|
||
|
|
// #define ST7735_INITB
|
||
|
|
// #define ST7735_GREENTAB
|
||
|
|
// #define ST7735_GREENTAB2
|
||
|
|
// #define ST7735_GREENTAB3
|
||
|
|
// #define ST7735_GREENTAB128 // For 128 x 128 display
|
||
|
|
// #define ST7735_GREENTAB160x80 // For 160 x 80 display (BGR, inverted, 26 offset)
|
||
|
|
// #define ST7735_REDTAB
|
||
|
|
// #define ST7735_BLACKTAB
|
||
|
|
// #define ST7735_REDTAB160x80 // For 160 x 80 display with 24 pixel offset
|
||
|
|
|
||
|
|
// If colours are inverted (white shows as black) then uncomment one of the next
|
||
|
|
// 2 lines try both options, one of the options should correct the inversion.
|
||
|
|
|
||
|
|
// #define TFT_INVERSION_ON
|
||
|
|
// #define TFT_INVERSION_OFF
|
||
|
|
|
||
|
|
|
||
|
|
// ##################################################################################
|
||
|
|
//
|
||
|
|
// Section 2. Define the pins that are used to interface with the display here
|
||
|
|
//
|
||
|
|
// ##################################################################################
|
||
|
|
|
||
|
|
// If a backlight control signal is available then define the TFT_BL pin in Section 2
|
||
|
|
// below. The backlight will be turned ON when tft.begin() is called, but the library
|
||
|
|
// needs to know if the LEDs are ON with the pin HIGH or LOW. If the LEDs are to be
|
||
|
|
// driven with a PWM signal or turned OFF/ON then this must be handled by the user
|
||
|
|
// sketch. e.g. with digitalWrite(TFT_BL, LOW);
|
||
|
|
|
||
|
|
// #define TFT_BL 32 // LED back-light control pin
|
||
|
|
// #define TFT_BACKLIGHT_ON HIGH // Level to turn ON back-light (HIGH or LOW)
|
||
|
|
|
||
|
|
// We must use hardware SPI, a minimum of 3 GPIO pins is needed.
|
||
|
|
// Typical setup for the RP2040 is :
|
||
|
|
//
|
||
|
|
// Display SDO/MISO to RP2040 pin D0 (or leave disconnected if not reading TFT)
|
||
|
|
// Display LED to RP2040 pin 3V3 or 5V
|
||
|
|
// Display SCK to RP2040 pin D2
|
||
|
|
// Display SDI/MOSI to RP2040 pin D3
|
||
|
|
// Display DC (RS/AO)to RP2040 pin D18 (can use another pin if desired)
|
||
|
|
// Display RESET to RP2040 pin D19 (can use another pin if desired)
|
||
|
|
// Display CS to RP2040 pin D20 (can use another pin if desired, or GND, see below)
|
||
|
|
// Display GND to RP2040 pin GND (0V)
|
||
|
|
// Display VCC to RP2040 5V or 3.3V (5v if display has a 5V to 3.3V regulator fitted)
|
||
|
|
//
|
||
|
|
// The DC (Data Command) pin may be labelled AO or RS (Register Select)
|
||
|
|
//
|
||
|
|
// With some displays such as the ILI9341 the TFT CS pin can be connected to GND if no more
|
||
|
|
// SPI devices (e.g. an SD Card) are connected, in this case comment out the #define TFT_CS
|
||
|
|
// line below so it is NOT defined. Other displays such at the ST7735 require the TFT CS pin
|
||
|
|
// to be toggled during setup, so in these cases the TFT_CS line must be defined and connected.
|
||
|
|
|
||
|
|
// For the Pico use these #define lines
|
||
|
|
#define TFT_MISO 0
|
||
|
|
#define TFT_MOSI 3
|
||
|
|
#define TFT_SCLK 2
|
||
|
|
#define TFT_CS 20 // Chip select control pin
|
||
|
|
#define TFT_DC 18 // Data Command control pin
|
||
|
|
#define TFT_RST 19 // Reset pin (could connect to Arduino RESET pin)
|
||
|
|
//#define TFT_BL // LED back-light
|
||
|
|
|
||
|
|
//#define TOUCH_CS 21 // Chip select pin (T_CS) of touch screen
|
||
|
|
|
||
|
|
// ##################################################################################
|
||
|
|
//
|
||
|
|
// Section 3. Define the fonts that are to be used here
|
||
|
|
//
|
||
|
|
// ##################################################################################
|
||
|
|
|
||
|
|
// Comment out the #defines below with // to stop that font being loaded
|
||
|
|
// The ESP8366 and ESP32 have plenty of memory so commenting out fonts is not
|
||
|
|
// normally necessary. If all fonts are loaded the extra FLASH space required is
|
||
|
|
// about 17Kbytes. To save FLASH space only enable the fonts you need!
|
||
|
|
|
||
|
|
#define LOAD_GLCD // Font 1. Original Adafruit 8 pixel font needs ~1820 bytes in FLASH
|
||
|
|
#define LOAD_FONT2 // Font 2. Small 16 pixel high font, needs ~3534 bytes in FLASH, 96 characters
|
||
|
|
#define LOAD_FONT4 // Font 4. Medium 26 pixel high font, needs ~5848 bytes in FLASH, 96 characters
|
||
|
|
#define LOAD_FONT6 // Font 6. Large 48 pixel font, needs ~2666 bytes in FLASH, only characters 1234567890:-.apm
|
||
|
|
#define LOAD_FONT7 // Font 7. 7 segment 48 pixel font, needs ~2438 bytes in FLASH, only characters 1234567890:-.
|
||
|
|
#define LOAD_FONT8 // Font 8. Large 75 pixel font needs ~3256 bytes in FLASH, only characters 1234567890:-.
|
||
|
|
//#define LOAD_FONT8N // Font 8. Alternative to Font 8 above, slightly narrower, so 3 digits fit a 160 pixel TFT
|
||
|
|
#define LOAD_GFXFF // FreeFonts. Include access to the 48 Adafruit_GFX free fonts FF1 to FF48 and custom fonts
|
||
|
|
|
||
|
|
// Comment out the #define below to stop the SPIFFS filing system and smooth font code being loaded
|
||
|
|
// this will save ~20kbytes of FLASH
|
||
|
|
#define SMOOTH_FONT
|
||
|
|
|
||
|
|
|
||
|
|
// ##################################################################################
|
||
|
|
//
|
||
|
|
// Section 4. Other options
|
||
|
|
//
|
||
|
|
// ##################################################################################
|
||
|
|
|
||
|
|
// For the RP2040 processor define the SPI port channel used, default is 0
|
||
|
|
// #define TFT_SPI_PORT 1 // Set to 0 if SPI0 pins are used, or 1 if spi1 pins used
|
||
|
|
|
||
|
|
// Define the SPI clock frequency, this affects the graphics rendering speed. Too
|
||
|
|
// fast and the TFT driver will not keep up and display corruption appears.
|
||
|
|
// With an ILI9341 display 40MHz works OK, 80MHz sometimes fails
|
||
|
|
// With a ST7735 display more than 27MHz may not work (spurious pixels and lines)
|
||
|
|
// With an ILI9163 display 27 MHz works OK.
|
||
|
|
|
||
|
|
// #define SPI_FREQUENCY 1000000
|
||
|
|
// #define SPI_FREQUENCY 5000000
|
||
|
|
// #define SPI_FREQUENCY 10000000
|
||
|
|
// #define SPI_FREQUENCY 20000000
|
||
|
|
// #define SPI_FREQUENCY 32000000
|
||
|
|
#define SPI_FREQUENCY 70000000
|
||
|
|
|
||
|
|
// Optional reduced SPI frequency for reading TFT
|
||
|
|
#define SPI_READ_FREQUENCY 20000000
|
||
|
|
|
||
|
|
// The XPT2046 requires a lower SPI clock rate of 2.5MHz so we define that here:
|
||
|
|
#define SPI_TOUCH_FREQUENCY 2500000
|
||
|
|
|